Installing Recessed Ceiling Box Lights

What do you need to install recessed ceiling box lights? You need 6 recessed can lights, two 4'x8' sheets of birch plywood that are 3/4" thick each, paint (e.g., Ace Sensations Ceiling White), a couple of ladders, skim coat, utility knife, tape measure, blue chalk and chalk line, reciprocal saw, pencil, stud finder, level, sander, table saw, circular saw, hammer, nails, and glue.

sheetrock prices

Select a spot on the ceiling where you want to position the recessed boxes. Take a chalk and mark the spot carefully with accurate measurements. Consider the distance from the wall lying parallel from the line you are drawing.

SHEETROCK PRICES

Next, create an inspection hole. An inspection hole is very crucial to see what is happening with the electric wires on the ceiling! Measure the section to be cut carefully and use a hammer to create the inspection hole. The opening has to be removed from the structure using a reciprocal saw. Take care when you are doing this task. Do not cut electric cables while doing this or you can cause serious trouble.

After you have cut out the rafters, place a frame at the ends. The opening is removed with the help of drywall. The centre portion has to withstand all the load. Are the cross beams concerning you? Do you want to get rid of them? Try using a hammer in this case. What do you do with the load that the beams supported all along? Place a double header at the end of the drywall to take care of the load, which can be a good option.

Use a table saw to cut pieces of plywood. To make the right shape on it, make measurements taking into consideration the shape and size of the recessed boxes. Dig holes for the recessed lights by using a sharp cutting instrument. You have to dig a minimum of one and a maximum of six holes. Fix the boxes inside the rafters to get a better effect. You can then put the can light above the boxes

Then comes the role of glue and nails. Use these to seal the boxes in the proper way. Smoothen the inside surfaces of walls using a sandpaper. Do it in circular movements so no nicks on the wood remain. You want to get rid of any nicks in the wood and make sure the surface is clean. Finish the job by applying paint on the ceiling and the boxes.

You work is done! Just wait for the paint to dry up. You can then place the lights into these recessed boxes and guess what? You are done! Wasn't that easy? If you want to get comprehensive information about ceiling box lighting, you can refer to various online resources or even books available on these topics. If you do not have all the supplies needed, try to find the best deals online and get all the supplies at prices you can afford.

Installing Recessed Ceiling Box Lights

Alvin Carson has over 3 years of experience in writing expert articles and product reviews in many different areas. If you are interested in lamps and lighting you can visit his latest website about swing arm lamp [http://www.swingarmlamptips.com] and even find out everything you need to know about swing arm wall lamp [http://www.swingarmlamptips.com/swing-arm-wall-lamp.html].

SHEETROCK PRICES

Recessed Ceiling Box Lighting

We've all seen the basic florescent lighting fixture. Bare, bald, bland and industrial looking lighting isn't the way to go in your interior design much less your garage space. That's where recessed box ceiling lights come into play. Best of all, you can install these recessed light sources into an existing kitchen, bathroom or laundry space with ease. Use this guide and you'll be on your way to getting the most out of your basic florescent tube lighting.

sheetrock prices

Before you begin

SHEETROCK PRICES

Before doing any electrical work, always turn off the breaker to the source. You can test if the power is shut off by testing it with an electrical meter. You can buy these for less than at any hardware store. If you're not sure, just turn off the breaker to the entire house. Be sure you have a flashlight handy to work in the now dark place.

Besides electrical wiring causing shocks, the recessed area where the light fixture is going to be installed in needs to be checked for structural irregularities that might make this job impossible. As long as there is room between joists, trusses or other structural material, you can remove the material and create the box; otherwise, you will need to choose a suitable location for your recessed light.

Padding out the space

Ensure that your lighting fixture is going to fit into the space with a quick measurement. You're going to want to add a minimum of two inches of space around the ballast on all sides. This will prevent any fire problems from occurring. That means if you're going to use ½ inch drywall, you'll need to add an extra three inches to the space around the box. Using a few studs or other suitable deadwood material, frame the box so that each side is plumb and square.

Trimming

Trimming the interior or exterior of the box out is the next step. First, install the wiring and ceiling light fixture into the center of the opening. Now drywall can be attached and cut around the inside of the recessed box. Next, attach a piece of trim around the inside edge of the recessed box. Cut the trim on 45 degree angles on each end to get a picture frame look. Ensure that the frame hangs in on each side ½ inches. Square the trim using the 3-4-5 measuring method. This is accomplished by measuring in the vertical direction three inches, then in the horizontal four inches. Now connect the two marks with a diagonal measurement. If it equals five, then the frame is square. If it's not, some minor adjustments may be needed to make the frame square. Once the frame is square a piece of frosted glass or crushed ice plastic may be used to cover the florescent ballast.

Recessed Ceiling Box Lighting

Need to find those ceiling lights? Visit http://www.arcadianlighting.com/ceiling-lights.html today! And for even more lighting inspirations, check out http://www.arcadianlighting.com

SHEETROCK PRICES